Rainier Falcons > The FalconForum  

Go Back   Rainier Falcons > The FalconForum > Blogs


It Runs... Again

Posted 04-10-2011 at 12:02 PM by pbrown
Updated 04-10-2011 at 12:07 PM by pbrown

Yesterday was spent finishing up the EDIS8 ignition system. Most of that time was fabricating the VR sensor bracket and 36-1 toothed wheel and waiting for paint to dry.

I made the final wire connections, connected the battery, and turned the key.Nothing. Hmmm. I tried again and again. Thinking it is now flooded I enabled flood clear mode (throttle pedal greater that 75% open disables fuel when cranking). Suddenly it started but ran poorly and had a strange whistle. I looked under...
pbrown's Avatar
Posted in Uncategorized
Views 6501 Comments 0 pbrown is offline Edit Tags

Some work on the new ignition

Posted 03-28-2011 at 10:36 PM by pbrown
Updated 03-29-2011 at 08:58 AM by pbrown

I've been working a bit on the ignition. I have the coil packs mounted. I found some room for them in front of the left head. I used the power steering pump bracket as a base. This bracket is made from 1/8" mild steel. Those coils won't go anywhere.

The EDIS module ended up just under the passenger side hood hinge. All the wiring to the coils is done as well at the power leads. I just need to work on the VR sensor.

There are some factory noise filters for the system...
pbrown's Avatar
Posted in 62 Falcon, EFI
Views 9672 Comments 2 pbrown is offline Edit Tags

Progress on Some Issues

Posted 03-14-2011 at 12:00 PM by MacDee
Updated 03-18-2011 at 03:13 PM by MacDee

Another progress report….

In my last report I believe I mentioned finding a cracked push rod over at Carter’s place last fall. I had driven it over there so we could verify the cam timing. The “cup” at the top of one of the push rods was cracked, and a piece of it broke off when I poked at it. Carter observed from the wear pattern that it looked as if it had only been wearing around the lip of the cup, not down in the cup itself; as though the ball on the end of the adjuster...
MacDee's Avatar
Senior Forum User
Posted in Uncategorized
Views 5064 Comments 0 MacDee is offline Edit Tags

LEDs for the Falcon

Posted 02-14-2011 at 11:27 PM by pbrown

I've been looking for the perfect LED setup for the Falcon for a while. Most of these just don't work well because the LEDs get oriented to only face one direction. The Falcon lens is actually designed to surround the bulb and focus the light sort of like a Fresnel lens. When the typical LED bulb is used the overall light is focussed at the center and it looks dim overall.

Well, I have a solution. Look at the photos and see what I found. I bought a complete set (front and rear). They...
Attached Thumbnails
Click image for larger version

Name:	led_vs_bulb.jpg
Views:	1275
Size:	86.2 KB
ID:	61   Click image for larger version

Name:	led_install.jpg
Views:	1251
Size:	123.6 KB
ID:	62   Click image for larger version

Name:	led_compare.jpg
Views:	1209
Size:	71.2 KB
ID:	63  
pbrown's Avatar
Posted in 62 Falcon
Views 12780 Comments 7 pbrown is offline Edit Tags

More progress - Still a lot to do though.

Posted 02-11-2011 at 08:10 PM by pbrown
Updated 02-13-2011 at 10:59 AM by pbrown

I've been doing a lot of under hood wire cleanup. I removed most of the factory harness wrap to expose the wires. The unused wire was removed and the others neatly routed and secured. I still need to rewrap the harness. I'm waiting to finish up the new ignition system before wrapping it all up.

I just received a new 8" center section in a 3.4:1 gear ratio and four gear Trac-Lock. This will be fun. I plan to pull the whole rear end when this goes in. I'd like to weld on the brackets...
pbrown's Avatar
Posted in 62 Falcon, EFI
Views 3589 Comments 0 pbrown is offline Edit Tags

All times are GMT -7. The time now is 08:55 PM.

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2018, vBulletin Solutions, Inc.