Compression is within 10psi of each other with no real low cylinders why not just drive it. If you just got to spend money give her a complete tune up and maybe a 1/2 quart of atf a couple of weeks...
Type: Posts; User: olgraybeard
Compression is within 10psi of each other with no real low cylinders why not just drive it. If you just got to spend money give her a complete tune up and maybe a 1/2 quart of atf a couple of weeks...
Looked at my shop manual for a 63. The fuses are not for the headlights but there is a circuit breaker built into the switch. It doesn't give any more details than that. Lucky it usually doesn't...
After about 1 hour of running time my 63 Econoline pickup headlights start blinking does this have a circuit breaker (where is it located).
yes and yes Driveline NW Fife Washington does it and they replace the tube. Good people there.
Do yourself a favor and replace the whole rear axle. The housing may have been tweeked, plus it is easier.
OMG just like a real car!! ;>) These small victories are what keeps us going, don't try to explain to non car guys or gals
Well I been work on the EPup sense end of September. I got engine running great, allot of rewiring, replaced radiator with mustang unit, replaced starter, coil, starter solenoid, replaced generator...
Was there power to it? does it have a switch of some sort or just turn the headlight switch like the dome light
http://www.walmart.com/ip/StreetGlow-LED-1157-Brake-Tail-Light-Bulb-White/21631628?ci_src=14110944&ci_sku=21631628&sourceid=1500000000000003260530
or google "temperature gauge radiator hose connection" allot out there like this reasonable http://www.glowshiftdirect.com/water-hose-adapters.aspx
on my tractor I cut the raditor hose and made a piece with a threaded connection so the tip of the sensor was in the flow of the coolent (coupler welded to a piece of exhaust pipe)
Inside the van or inside the bed, should be the same, what I'm wondering is what it looks like open and closed and closed does it go under the rocker panel like a camper step would and when its open...
Being that my a_ _ was built to close to the ground and the sides of the pickup are fairly high it would be a good option to reach into the bed of the pickup if it is what I'm envisioning. Any pics...
Are those a aftermarket or OEM item
Where did you find one of these I'd love to have a pair of these for my E-pup.
Great minds think alike I'm doing the same only steel 1/4 ips steel pipe spacers as soon as I get rid of voltage regulator, it in the way right now (its not being used, I went with a one wire...
on my Enonoline pickup 1 1/2 top connection on right side and 1 3/4 on left side. On the mustang 1 1/2 on right and 1 3/4 on right. I guessing your Falcon is the same as the Mustang although the...
Well I got everything back together today, replaced exhaust manifold, new starter back on, alternator, replaced front right brake line, got emergency brake working and replaced radiator with one...
Well 5 hours later I finally got the last broken bolt out and the original threads chased and found out I left the exhaust manifold in my wife van, so I guess this is a good place to stop (it...
Made some good progress, I adjusted the linkage the 2-3 shift rod was out 1/2" and the bushing with Zerk fitting had no lube but it was clean so I filled it with grease. I think those were my...
Found vacuum leak,gasket under carb was broken. It now idles good. Broke 3 bolts getting cracked exhaust manifold off. Fixing them is next on list. Another site suggested I check the shifter linkage...
Which pick and pull and did it have a tranny
Need a 3 speed manual transmission (short shaft) for a 63 Econoline Pickup
It's running and charging, stomped on the brakes when putting it up on ramps and blew a brake line, all lines steel and rubber have to be replaced master cylinder works good and shoes are good. No...
Hal, you have a PM