Search:

Type: Posts; User: pbrown

Page 1 of 20 1 2 3 4

Search: Search took 0.04 seconds.

  1. Replies
    8
    Views
    2,024

    I had to step away for a while. I came back home...

    I had to step away for a while. I came back home and found this. It's an under dash booster setup. This will cleanup the engine side of the firewall.


    8060
  2. Replies
    8
    Views
    2,024

    Here is some work on the under dash sub-harness. ...

    Here is some work on the under dash sub-harness. This connects the rear of the bulkhead fittings to the new EFI controller. It's not complete. I need to get the shielded wire for the 36-1 crank...
  3. Replies
    8
    Views
    2,024

    The new ECU is mounted. It's mounted to the...

    The new ECU is mounted. It's mounted to the backside of the firewall right above the heater box. This is a big upgrade from the crappy attempt to mount the prior ECU with velcro. You can see the...
  4. Replies
    5
    Views
    3,150

    That was a fun day. I remember installing door...

    That was a fun day. I remember installing door wire looms in Gene's car. That was tricky.
  5. Replies
    8
    Views
    2,024

    I splurged for a new ECU. It uses the same...

    I splurged for a new ECU. It uses the same system as my old one (MS3x) but is a sealed box with proper connectors, warranty, and support.

    8039
  6. Replies
    8
    Views
    2,024

    I ordered the under dash brake booster kit today....

    I ordered the under dash brake booster kit today. It's a kit from RRS and relocates the clutch and brake masters to under the dash. This will clean up the firewall and make room for the coils...
  7. Replies
    8
    Views
    2,024

    More photos. 8036 8035 8037 ...

    More photos.

    8036

    8035

    8037


    Drilling giant holes in the firewall was scary. It will look good when done. All of the car's wiring will go through these two plugs.
  8. Replies
    8
    Views
    2,024

    Winter 23/24 Work - EFI Rewire

    It's been a while. Here's what I'm up to.

    Rewire under hood and upgrading to full sequential fuel and spark.
    Eight new coils
    Rewire with TXL wire throughout
    Deutsch HD30 series connectors at...
  9. Replies
    16
    Views
    1,603

    I didn't see any budget listed so thought I'd...

    I didn't see any budget listed so thought I'd throw this out. There are several of these belt systems available for the SBF. Many use the SN95 reverse rotation water pump and timing cover. This...
  10. Thread: Fitment check

    by pbrown
    Replies
    4
    Views
    433

    I have a 1" bar for a 65 Mustang in my 62 Falcon....

    I have a 1" bar for a 65 Mustang in my 62 Falcon. It fits fine.
  11. Replies
    16
    Views
    1,603

    I've seen kits for the 64/65 Falcon. I think the...

    I've seen kits for the 64/65 Falcon. I think the only part that wouldn't work would be the controls. I suspect the compressor, evap, condenser, etc would all fit. Maybe give them a call and see...
  12. Thread: I'm back!?

    by pbrown
    Replies
    3
    Views
    690

    Welcome back. I'm sure it will be awesome.

    Welcome back. I'm sure it will be awesome.
  13. Replies
    3
    Views
    680

    I've been watching this guy's solar channel....

    I've been watching this guy's solar channel.
    https://www.youtube.com/c/WillProwse

    One day I wanted to learn how jet engines work and git sucked into this one....
  14. Replies
    4
    Views
    715

    Check out Books4Cars. They are right here in...

    Check out Books4Cars. They are right here in Seattle. It's fun to go browse the shelves.

    https://books4cars.com/listings.php?findmake=Ford&model=Falcon&year=1963&type=Shop
  15. Replies
    143
    Views
    20,572

    How about PPG CopperHead for a color? This is a...

    How about PPG CopperHead for a color? This is a color that Stacey David created on TrucksTV. The Falcon curves would make this color pop.
    ...
  16. Replies
    2
    Views
    582

    Sad Day for the Bike Crowd

    https://www.autoblog.com/2021/01/19/austria-alps-motorcycle-museum-fire/#slide-2290019
  17. Replies
    21
    Views
    1,653

    Is a turnbuckle needed? It's by understanding...

    Is a turnbuckle needed? It's by understanding that's it's just there to account for manufacturing variations from the factory. If built in the car it should fit fine and still be removable.

    I...
  18. Replies
    778
    Views
    802,866

    Let us know what you find on shorter shocks. I'm...

    Let us know what you find on shorter shocks. I'm in the same boat.
  19. Replies
    21
    Views
    1,653

    There is a bolt in export brace make from heavt...

    There is a bolt in export brace make from heavt stanped steel. It's cheap. I did this can had it chrome plated.

    You could also build your own. Maybe something like the Global West version. It...
  20. Replies
    5
    Views
    1,250

    A great Seattle based fabricator is Eliot at...

    A great Seattle based fabricator is Eliot at Elhot Metal Fab. He's partnered with The Shop in SODO and I'm not sure what is required to get a car in there. I'd give "The Shop" a call and ask for...
  21. Replies
    25
    Views
    2,152

    All Falcons are welcome here.

    All Falcons are welcome here.
  22. Replies
    143
    Views
    20,572

    That 63 would work well as a gasser. It really...

    That 63 would work well as a gasser. It really needs a big block though. Maybe a 427 with a blower on top and dual quads. No hood.
  23. Replies
    3
    Views
    738

    Agreed. I need to spend some time restoring the...

    Agreed. I need to spend some time restoring the old links.
  24. Replies
    2
    Views
    666

    I'm not sure. I see what I can find. There's...

    I'm not sure. I see what I can find. There's probably an add-on for that.
  25. Replies
    3
    Views
    593

    Seems a bit slow on the forum

    Maybe everyone is having too much fun driving their Falcons to post anything.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4