Results 1 to 4 of 4

Thread: Strange lock button issue

  1. #1
    Join Date
    Jul 2013
    Location
    Federal Way
    Posts
    827

    Strange lock button issue

    Anyone seen this problem before??
    See the pics...every inside door lock button sticks up out of the door like this.
    Several different platic buttons, but some of the rods stick way out of the doors. In fact it's easy to bend them when you push down on the button to lock the door.
    I don't know if the plastic buttons are just not correct, or the rods inside are not correct...very strange. I'm assuming there must be a reason for it and someone else has had this problem?? As usual...thanks in advance!
    Attached Images Attached Images
    Don Bartlett
    Federal Way, WA
    61 Four Door Sedan
    144-6, 3 on the tree



  2. #2
    Buttons look right.

    Maybe the rods are in the latch incorrectly?

    Dunno you stumped me there.
    Nathan and Jen Cooper
    63 Sprint Hardtop "Dollora"
    63 Super deluxe squire wagon "Mayble"
    * this spot is vacant for future project*

  3. #3
    Not having looked into a 4-door car before, I'm not sure what it is either. I know the 2-door setup pretty good and these rods go down and loop upwards before they go into the latch assembly with a typical clip, like those used on carburetor linkages. Looks much like the letter "J" and perhaps someone pulled hard on it and bent the rod. They should stick up through the door maybe about 1/2" prior to screwing on the knobs. Over time these latches get gummed up and maybe it got harder and harder to unlock, causing the rods to get pulled further and further up. Look at the rods and if they are looking more like the letter "I" instead of "J" then they need to be bent back again and the latch lubed up.

    The rear doors, since the door lock is way forward of the latch, which is in the back of the door and the pull is in the front of the door, probably have some cantilever action up front to transfer up/down action to forward/back then back to up/down. This I'm uncertain of. Would need to see one for myself.
    Roger Moore

    63 "Flarechero"
    powered by: 347ci stroker | Tremec T5 | 8" 3:45 TracLoc rear



  4. #4
    Join Date
    Jul 2013
    Location
    Federal Way
    Posts
    827
    That totally makes sense. I'm wondering if they got bent down for some reason, then someone tried to pull them up with pliers and bent-stretched them. One of them is angled now.
    Guess it will all become clear when I dismantle the doors...that will have to wait...I plan to finally get the rear axle finished and back on the car this weekend and at least part of the front suspension back on.
    Thanks!
    Don Bartlett
    Federal Way, WA
    61 Four Door Sedan
    144-6, 3 on the tree



Similar Threads

  1. Odd idle circuit issue Edelbrock 1406
    By Luva65wagon in forum Tech Talk
    Replies: 3
    Last Post: September 26th, 2011, 05:22 PM
  2. Trunk Lock
    By oldford63 in forum Tech Talk
    Replies: 1
    Last Post: January 27th, 2009, 01:37 PM
  3. Ongoing electrical issue with not starting
    By icebox500 in forum Tech Talk
    Replies: 9
    Last Post: June 20th, 2008, 12:14 AM
  4. Shifting issue, plus others
    By Tex-Mex in forum Tech Talk
    Replies: 9
    Last Post: May 4th, 2008, 10:39 PM
  5. Falcon Wagon Electrical Start Issue
    By icebox500 in forum Tech Talk
    Replies: 6
    Last Post: January 17th, 2008, 12:07 AM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •