Rainier Falcons > The FalconForum  

Go Back   Rainier Falcons > The FalconForum > General Forums > Tech Talk

Reply
 
Thread Tools Display Modes
  #1  
Old 08-07-2014, 12:02 AM
Wilbur Wilbur is offline
Active Forum User
 
Join Date: Oct 2007
Location: Seattle
Posts: 118
Need assistance removing starter motor 200 inline six please

I have a 1964 Ford Falcon sedan with a 200 ci inline six and three speed top loader transmission. I'm replacing the clutch, well, removing it so I can figure out what went wrong inside.

I've removed the transmission today, now I'm attempting to remove the bell housing, and I've got all bolts off EXCEPT for the one at the top of the starter motor, it's a "high mount" starter motor.

I can't get in their with an open end wrench, and if I use a socket wrench, I can get the socket on there but there isn't enough clearance to turn the wrench at all.

It got dark before I could try other methods but I figure it doesn't hurt to get online here and ask if anyone has this setup in their Falcon and has removed their starter motor on a high mount starter mated to their 200 ci inline six motor with 3 speed top loader trans.

Tomorrow I hope to figure it out but just in case I'm also asking on this forum. Thanks!
Reply With Quote
  #2  
Old 08-07-2014, 06:55 AM
doghows's Avatar
doghows doghows is offline
Senior Forum User
 
Join Date: Aug 2009
Location: Sequim
Posts: 2,110
You may have to use a crows foot? It looks like the end of an open end wrench but has a end on it your ratchet would fit into. If that makes any sense. Or (without seeing it) can you get a wobbly onto the socket so you can get the ratchet on? HTH.
__________________
63 Sedan Delivery
5.0 HO EFI AOD 8" rear
Reply With Quote
  #3  
Old 08-07-2014, 09:16 PM
SmithKid's Avatar
SmithKid SmithKid is offline
Paid Chapter Member
 
Join Date: Feb 2007
Location: Everett
Posts: 916
I have a (starter) wrench I inherited from my Dad that looks like this, and has been very handy over the years. I'll be home on the evening of the 10th if you'd like to borrow it.
Attached Images
File Type: jpg starter wrench.jpg (2.7 KB, 4 views)
__________________


Gene Smith
Everett, WA
'65 Ranchero Deluxe
302, 4-Spd
Granada Discs
Reply With Quote
  #4  
Old 08-07-2014, 11:50 PM
Wilbur Wilbur is offline
Active Forum User
 
Join Date: Oct 2007
Location: Seattle
Posts: 118
Thanks for the replies Dog and Smith. Good news, I tried again but this time using a special tool called SUNLIGHT rather than straining as I did last night to see what I could after the sun had gone down.

In the light of day I was able to see that if I took a long extension and kept the wrench some 7 or so inches away I was able to get the clearance needed to turn that bolt and finish removing the starter motor, and thus bell housing.

Once I got the clutch out of the car, I saw what my original problem was, one of the "fingers" of the three fingers on the pressure plate SNAPPED one night when I pushed the clutch pedal in to start off from a red light.

I heard a "bang" and the clutch pedal went to the floor and stayed there. I started the car in gear and drove it home.

So now I must find a new pressure plate and clutch. The clutch has little wear on it but I'll replace it. The pressure plate, whoever rebuilt this, they put in the wrong finger, the one finger doesn't match the other two and there is uneven wear on what is left of it.

O'Reilly's does have these parts but they are made in China, so I won't be using those parts. I found a place that rebuilds clutches etc. so I'll let them have a look at things.

Again, thank you for offering your advice, these forums are wonderful places to help one another out. Thank you. :-)
Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Need some assistance Jerry Kirby Chit Chat 2 05-27-2010 11:49 AM
removing door panels on the 1965 falcon... supertape Tech Talk 8 06-19-2008 09:41 PM
Starter Not Starting... icebox500 Tech Talk 2 09-26-2007 07:06 PM
Battling with Starter Boss 347 Tech Talk 2 07-25-2007 10:30 PM
Bodywork Assistance pbrown Events and Announcements 3 05-01-2007 11:44 AM


All times are GMT -7. The time now is 09:14 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2018, vBulletin Solutions, Inc.