Rainier Falcons > The FalconForum  

Go Back   Rainier Falcons > The FalconForum > General Forums > Tech Talk

Reply
 
Thread Tools Display Modes
  #1  
Old 05-20-2017, 11:01 AM
beerbelly beerbelly is offline
Active Forum User
 
Join Date: Nov 2015
Posts: 76
Windshield and headliner questions

Next year's project is a new windshield, front and rear seals and a new headliner. I haven't yet decided if a friend and I are going to try to tackle this, or pay a pro to do it. I'm not too worried about the rear glass with the plain seal- I've done flat glass before.

Could someone please school me on the correct way to remove the rock hard windshield seal without screwing up the stainless trim, and the right way to install them?
__________________
1965 Ranchero Deluxe
factory 289 4 speed car
Reply With Quote
  #2  
Old 05-21-2017, 08:13 AM
Luva65wagon's Avatar
Luva65wagon Luva65wagon is offline
Chapter President
 
Join Date: Oct 2006
Location: Lynnwood
Posts: 4,410
Blog Entries: 4
Best way to remove it is with the windshield and rubber as a whole. From inside cut the sealing lip away so the entire windshield/rubber/stainless can be pushed away from the car from inside.

Remove trim from glass and rubber is now easy.

On sawhorses working with outside of glass/trim upwards, apply a thin bead of windshield bedding (stuff that is made of tar and doesn't harden you get from autobody supply) into the windshield groove of the new seal and insert the glass into the rubber. Get it all centered correctly! If possible, use masking tape to hold it on. Leave trim grooves available with no tape covering them. Then pre-insert the trim (do whatever straightening and polishing first) with the exception of the two corner pieces, and using masking tape to hold all this together. Now flip the assembly over and insert your pull rope with the ends near center/bottom. Tape the ends of the rope to the windshield. Apply a good bead of bedding to body and rubber and place glass/rubber/trim into body and with two outside and one inside pull the seal into the car slowly while users outside apply firm pressure as you go.

It may get a little messy so be prepared to use mineral spirits to clean up what oozes out. If you can mask off the headliner at the top, that will save you time scrubbing that of the tar. Don't try to go too easy on the tar to avoid this, since a leaking winshield is a far worse hassle.

Once the seal is all inside, do some flat-handed pats to the windshield to work it firmly into place. Clean some more. Then insert screws and corner pieces.

I'd say "have fun" but it's not really. But it is rewarding.
__________________
Roger Moore

63 "Flarechero"
powered by: '65 289-V8 | T5 | 8" TracLoc rear


Reply With Quote
  #3  
Old 05-24-2017, 12:52 PM
beerbelly beerbelly is offline
Active Forum User
 
Join Date: Nov 2015
Posts: 76
Thanks for the info; very helpful. Now I have about a year to work up the nerve to do it!
__________________
1965 Ranchero Deluxe
factory 289 4 speed car
Reply With Quote
  #4  
Old 06-07-2017, 09:22 PM
Voodoofalcon's Avatar
Voodoofalcon Voodoofalcon is offline
Paid Chapter Member
 
Join Date: Nov 2011
Location: Burien
Posts: 113
Headliner not nearly as bad as I thought it would be to do yourself . I can come help when the time comes. Just make sure you mark your rods when you pull the old one out.
__________________

1965 Hardtop, 289, Top loader, Torino power disk brakes, Tilt steering, 2 speed int wipers

Mike Spears
Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Free headliner,hinge pin bushing set,molding clips 642dw Cars and Parts For Sale or Trade 5 07-19-2017 11:18 AM
62 Wagon headliner bows. friver609 Parts Wanted 1 01-17-2015 10:30 PM
New Headliner 64SprintV8 Chit Chat 4 11-22-2011 02:45 PM
Windshield BadBird Cars and Parts For Sale or Trade 0 09-13-2010 04:25 PM
Headliner BadBird Tech Talk 8 06-16-2010 09:29 AM


All times are GMT -7. The time now is 04:09 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2018, vBulletin Solutions, Inc.