Page 2 of 7 FirstFirst 1234 ... LastLast
Results 16 to 30 of 100

Thread: Powder coating done cheap

  1. #16
    Join Date
    Aug 2009
    Location
    Sequim
    Posts
    2,117
    Not very easy. The dark red is actually a primer that you paint on the center removable piece. I normally only coat the housing itself not the rest of it.
    63 Sedan Delivery
    5.0 HO EFI AOD 8" rear

  2. #17
    The Pumpkin is done in Red Oxide primer from the factory. They never painted them. You can get that anywhere, of course, but you should also get a new set of lock nuts for when you reassemble it, along with a new gasket. The new nuts come with new copper flat washers, which actually seal the bolt portion from leaking..

    If anyone else has stuff to send over to Steve, be sure to let me know. I'm heading over there on Friday and have a little room left.

    Hum... I should look around for some stuff too...
    Last edited by Luva65wagon; December 23rd, 2013 at 01:14 PM. Reason: copper washer mention
    Roger Moore

    63 "Flarechero"
    powered by: 347ci stroker | Tremec T5 | 8" 3:45 TracLoc rear



  3. #18
    So when did a 61 4 door with a 144 come with a 8" and a removable 3rd member??

  4. #19
    Join Date
    Jul 2013
    Location
    Federal Way
    Posts
    906
    I'm not sure I understand what you guys are talking about. Are we talking about the same style of reAr axle? Pic below. The only bolts are the bolts for the cover. Everything else is basically one piece...(brake stuff is all removed..) I assume it's possible to take off the tubes but I don't have any hardware for putting them back on. Why could it not all be painted (powder coated) black at once?
    Attached Images Attached Images
    Don Bartlett
    Federal Way, WA
    61 Four Door Sedan
    144-6, 3 on the tree



  5. #20
    Join Date
    Aug 2009
    Location
    Sequim
    Posts
    2,117
    Ok here is the deal. The cover needs to be off. All gears bearings and seal out, if the axle looks like the picture I can't do it. I will melt the seal when I bake it in the oven.
    Did you remove all the internals? I need an empty housing, meaning the tubes and center that is attached to the tubes only. If the cover and pinion is all still in place don't send it over it needs to be completely taken apart..
    Roger if you read this you will know what I need hopefully we are good.. Thanks Steve..
    63 Sedan Delivery
    5.0 HO EFI AOD 8" rear

  6. #21
    Join Date
    Jul 2013
    Location
    Federal Way
    Posts
    906
    Yep, the pic was just to show which one, but whats on its way to you is a totally empty housing only, with the tubes, and it's clean. The only thing I didn't remove which now I wonder about is the vent.
    Don Bartlett
    Federal Way, WA
    61 Four Door Sedan
    144-6, 3 on the tree



  7. #22
    Join Date
    Aug 2009
    Location
    Sequim
    Posts
    2,117
    Nope your dead on. Now were on the same page, you'll love it when it's done thanks.
    63 Sedan Delivery
    5.0 HO EFI AOD 8" rear

  8. #23
    That's the trouble with multitasking - you forget who what when how sometimes. I didn't look that close at what you gave me (inside the cardboard wrapper) so I forgot we were talking a 7.25" rear-end. These didn't have the red-oxide pumpkin. It was all black. Did you send over the back cover? Was it in there?

    When I drop it off Steve and I can look at it and remove anything that should be removed that wasn't. No worries.

    Sorry for the brain fart.
    Roger Moore

    63 "Flarechero"
    powered by: 347ci stroker | Tremec T5 | 8" 3:45 TracLoc rear



  9. #24
    Join Date
    Jul 2013
    Location
    Federal Way
    Posts
    906
    No worries...but the pumpkin part does look like red oxide. (feel free to open the cardboard if you're curious.) I did not send the cover...I'll take care of that myself. Do you guys know where I can get replacement bolts and washers for the cover?
    Don Bartlett
    Federal Way, WA
    61 Four Door Sedan
    144-6, 3 on the tree



  10. #25
    Join Date
    Aug 2009
    Location
    Sequim
    Posts
    2,117
    Don got your parts, they are perfect.. Ill get them done next week and see what we can do to get them back over to you. Thanks Steve
    63 Sedan Delivery
    5.0 HO EFI AOD 8" rear

  11. #26
    Join Date
    Aug 2009
    Location
    Sequim
    Posts
    2,117
    Don, I got your parts cleaned today, and it plan on coating them tomorrow. I post up a few pics when done if you don't mind.
    Then we just need to figure out how to get them back to you.. I think we are going to have a tech day in the next weekend or so to put Gina's car back together so maybe Roger can shuttle them back for us in his new space shuttle car!!
    Anyway stay tuned they should look great.
    Last edited by Luva65wagon; December 30th, 2013 at 11:09 PM.
    63 Sedan Delivery
    5.0 HO EFI AOD 8" rear

  12. #27
    Quote Originally Posted by doghows View Post
    maybe Roger can shuttle them back for us in his new space shuttle car!!
    My Storm Trooper car.
    Roger Moore

    63 "Flarechero"
    powered by: 347ci stroker | Tremec T5 | 8" 3:45 TracLoc rear



  13. #28
    Join Date
    Aug 2009
    Location
    Sequim
    Posts
    2,117
    My bad, that's what I meant. Storm trooper!!
    63 Sedan Delivery
    5.0 HO EFI AOD 8" rear

  14. #29
    Join Date
    Aug 2009
    Location
    Sequim
    Posts
    2,117
    Ok here you go Don.

    Ready for the color and into the oven!
    Attached Images Attached Images
    63 Sedan Delivery
    5.0 HO EFI AOD 8" rear

  15. #30
    Join Date
    Aug 2009
    Location
    Sequim
    Posts
    2,117
    And through the magic of the internet, done.
    Attached Images Attached Images
    63 Sedan Delivery
    5.0 HO EFI AOD 8" rear

Similar Threads

  1. Real Cheap 61, Roger's next save?
    By BPVan in forum Cars and Parts For Sale or Trade
    Replies: 3
    Last Post: September 14th, 2013, 10:50 PM
  2. powder
    By falcon cobra in forum Tech Talk
    Replies: 1
    Last Post: April 13th, 2013, 02:42 PM
  3. Powder coating
    By modified17 in forum Tech Talk
    Replies: 3
    Last Post: March 25th, 2010, 08:22 AM
  4. Powder Coating
    By BadBird in forum Tech Talk
    Replies: 4
    Last Post: November 30th, 2008, 03:01 AM
  5. Misc. Six Cylinder Parts - Cheap!
    By redfalken in forum Cars and Parts For Sale or Trade
    Replies: 1
    Last Post: June 22nd, 2008, 08:12 AM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •