Results 1 to 6 of 6

Thread: Strut rod bushings

  1. #1

    Strut rod bushings

    I'm doing the strut rod bushings on my 63 Falcon and bought the poly units. Made by enegry supension. They appear much longer than the stock ones.

    I'm afraid that they will limit the adjustment too much. Has anyone else used These? I'm tempted to put them in the lathe and take a bit off the tapered end. They are so stiff that they won't compress much if any.


  2. #2
    Bill, Though I don't think they are the same as we put into Don's car, they do "look" the same. Here's the post I did on that:

    http://www.rainierfalcons.com/forums...&postcount=445
    Roger Moore

    63 "Flarechero"
    powered by: 347ci stroker | Tremec T5 | 8" 3:45 TracLoc rear



  3. #3
    I replaced mine with stock rubber bushings. I remember reading a lot of bad things about running poly strut rod bushings. But they sell them so they must not be to dangerous

    1965 Hardtop, 289, Top loader, Torino power disk brakes, Tilt steering, 2 speed int wipers

    Mike Spears

  4. #4
    Yup these were a waste of money. They are the wrong size and way to stiff.

  5. #5

    Strut rod bushings

    I have rubber bushings on my car.

    Here is an interesting alternative that I read about but have not personally tried:

    High performance strut rod bushings: http://www.jegs.com/i/Global-West/45...oductId=760572
    Fits 1962 – 1965 Ford Falcon. “If adjustable strut rods are not in your budget, high-density rubber strut rod bushings would be your best alternative. The rubber bushings are stiffer than the factory type and have just enough forgiveness to allow the suspension to move without overstressing the strut rod. These bushings are recommended if the car is used as a daily driver and is not raced.” “High durometer bushings will control lower control arm location with limited deflection and still allow pivot over standard factory durometer. Provides better alignment, cornering, and braking control. Easy installation. No modifications needed. Too high of a durometer bushing in this location can cause strut rod failure due to too much resistance in the direction of pivot. That is why there is rubber in this location over other high density plastics.”
    Dennis Pierson
    Tampa, FL
    "The Wonder Falcon"

    '63 Futura Hardtop (260, Ford-O-Matic, bench seat)

  6. #6
    Quote Originally Posted by ew1usnr View Post
    I have rubber bushings on my car.

    Here is an interesting alternative that I read about but have not personally tried:

    High performance strut rod bushings: http://www.jegs.com/i/Global-West/45...oductId=760572
    Those actually look good. $70 is kinda spendy for what it is, but not a ton more than stock replacements.

Similar Threads

  1. Disintegrated Strut Bushings
    By ew1usnr in forum Tech Talk
    Replies: 30
    Last Post: September 12th, 2017, 02:56 PM
  2. Shackle bushings
    By doghows in forum Tech Talk
    Replies: 10
    Last Post: March 29th, 2011, 10:20 AM
  3. Door hinge bushings
    By EdsFunny in forum Tech Talk
    Replies: 4
    Last Post: January 7th, 2011, 06:33 PM
  4. leaf spring bushings..
    By Nathan289 in forum Tech Talk
    Replies: 0
    Last Post: May 17th, 2010, 10:59 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •